Fracture Gradient Reduction Due to Water Depth

​

Fracture gradient is one of the critical information which drilling engineers need to know in order to design drilling programs. For the well control stand point, the fracture gradient directly affects on how much influx volume can be successfully contained in the wellbore. If the wellbore pressure is over the fracture pressure, formations would be broken down and this situation will result in loss of drilling fluid into formations. Additionally, it might lead to well control situation because of loss of hydrostatic pressure. Fracture gradient is quite straight forward for land operation because it will not be reduce due to water column. However, the fracture gradient will be reduced in deepwater environment. In this article, we will discuss why water depth can cause the reduction in fracture gradient.​

Basically, the fracture gradient is related to fluids occupying in pore spaces of rock and weight of rock which are called overburden pressure. Generally, the overburden of a typical sedimentary is about 1.0 psi/ft (19.2 ppg). Rocks will be fractured when the wellbore pressure exceeds the confining stresses acting on it. If we make a general assumption that the overburden pressure causes the minimum confining stress of the rock. Then the formation fracture gradient will not be 1.0 psi/ft if the location is offshore.​

Note: this assumption is made in order to help you get more understanding on how and why water depth can decrease the formation fracture gradient.​

Water has less density than rock and when it is calculated into overburden pressure, it will reduce overall overburden pressure. For the calculations in this article, we will use 1.0 psi/ft as the overburden of the rock.​

Let’s take a look at the examples below;​

1[SUP]st[/SUP] Example – Comparison between land and offshore location at 4,000’ TVD.​

Land operation at 4,000’ TVD (Figure 1): ​

Figure 1 – Land operation at 4,000’ TVD​

​

Overburden at 4,000’ TVD = 4,000 x 1 = 4,000 psi​

Convert 4,000 psi at 4,000’ TVD in to ppg = 4,000 ÷ (0.052 x 4,000) = 19.23 ppg​

Offshore operation at 4,000’ TVD with a water depth of 2,000 ft (Figure 2)​

Water density is 0.45 psi/ft.​

Figure 2 – Offshore operation – 2000 ft water depth​

Overburden pressure = (0.45 x 2,000) + (1.0 x 2,000) = 2,900 psi​

Convert 2,900 psi at 4000’ TVD in to ppg = 2,900 ÷ (0.052 x 4,000) = 13.94 ppg​

From the first example, you will see that at 4,000’ TVD, water depth will reduce the overburden from 19.23 ppg to 13.94 ppg.​

2[SUP]nd[/SUP] Example – Comparison between land and offshore location at 15,000’ TVD.​

Land operation at 15,000’ TVD (Figure 3)​

Overburden at 15,000’ TVD = 15,000 x 1 = 15,000 psi​

Convert 15,000 psi at 15,000’ TVD in to ppg = 15,000 ÷ (0.052 x 15,000) = 19.23 ppg​

Figure 3 – Land operation at 15,000’ TVD​

Offshore operation at 15,000’ TVD with a water depth of 2,000 ft (Figure 4)​

We will use the same water depth of 2,000 ft but the well depth is at 15,000’ TVD for offshore operation.​

Figure 4 – Offshore operation at 15,000’ TVD​

Overburden pressure = (0.45 x 2,000) + (1.0 x 13,000) = 13,900 psi​

Convert 2,900 psi at 4000’ TVD in to ppg = 13,900 ÷ (0.052 x 15,000) = 17.82 ppg​

As you can see in the second example, the overburden of the formation still decreases due to water depth. However, it has less effect than the shallow well.​

Water depth will reduce the formation fracture pressure and offshore wells will have smaller margin between mud weight and fracture pressure than land wells because of water depth effect. At the same water depth, the fracture pressure at the shallower section will be decreased more than the deeper depth. What’s more, particularly at a shallow depth where the average overburden is greatly reduced by water column, more casing strings are required to reach the plan casing depth.​

Reference books: Well Control Books
​