درخواست های مرتبط با | حلّ تکالیف و مسائل درسی مهندسی شیمی

پیرجو

مدیر ارشد
مدیر کل سایت
مدیر ارشد
1287986292_37.jpg

سلام بر دوستان عزیز
خواهشمند است تکالیف دانشگاهی خود را که از پس حل آن بر نیامده اید را اینجا قرار بدهید

 
آخرین ویرایش توسط مدیر:

پیرجو

مدیر ارشد
مدیر کل سایت
مدیر ارشد
 

mim-shimi

عضو جدید
کاربر ممتاز
THERMO 1

A piston–cylinder device contains 0.8 kg of an ideal
gas. Now, the gas is cooled at constant pressure until its temperature
decreases by 10°C. If 16.6 kJ of compression work
is done during this process, determine the gas constant and
the molar mass of the gas. Also, determine the constant volume
and constant-pressure specific heats of the gas if its
specific heat ratio(C
p/Cv) is 1.667.






A mass of 0.2 kg of saturated refrigerant-134a is contained in a piston–cylinder device at 200
kPa. Initially, 75 percent of the mass is in the liquid phase. Now heat is transferred to the
refrigerant at constant pressure until the cylinder contains vapor only. Show the process on a
[FONT=TimesNewRoman,Italic]P-[/FONT][FONT=Arial,Italic]v

[/FONT]
diagram with respect to saturation lines. Determine (​
[FONT=TimesNewRoman,Italic]a[/FONT]) the volume occupied by the refrigerant
initially, (
[FONT=TimesNewRoman,Italic]b[/FONT]) the work done, and ([FONT=TimesNewRoman,Italic]c[/FONT]) the total heat transfer.



A rigid tank containing 0.4 m
3 of air at 400 kPa and
30°C is connected by a valve to a piston–cylinder device with
zero clearance. The mass of the piston is such that a pressure
of 200 kPa is required to raise the piston. The valve is now
opened slightly, and air is allowed to flow into the cylinder
until the pressure in the tank drops to 200 kPa. During this
process, heat is exchanged with the surroundings such that
the entire air remains at 30°C at all times. Determine the heat transfer for this process



نگین اینا آسونه ها:D...هنوز روشون فکر نکردم..به هر حال کار از محکم کاری عیب نمی کنه;)
احتمالا دوشنبه باید تحویل بدیمشون.

 

mim-shimi

عضو جدید
کاربر ممتاز
سلام
ماشاالله استاد ما زیادی فعاله;)
فعلا سوالا رو میزارم اینجا..لطف کنین روش فکر کنین..شنبه اشکالامو ازتون میپرسم:)
ممنون از همه



For All these problem you need to determine your control volume schematically
.
Refrigerant-134a enters an adiabatic compressor as saturated vapor at -24°C and leaves at 0.8
MPa and 60°C. The mass flow rate of the refrigerant is 1.2 kg/s. Determine
(​
[FONT=TimesNewRoman,Italic]a[/FONT]) the power input to the compressor and ([FONT=TimesNewRoman,Italic]b[/FONT]) the volume
flow rate of the refrigerant at the compressor inlet.


Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 10 MPa,
450°C, and 80 m/s, and the exit conditions are 10 kPa, 92 percent quality, and 50m/s. The mass
flow rate of the steam is 12 kg/s. Determine (
[FONT=TimesNewRoman,Italic]a[/FONT]) the change in kinetic energy, ([FONT=TimesNewRoman,Italic]b[/FONT]) the power output,
and (
[FONT=TimesNewRoman,Italic]c[/FONT]) the turbine inlet area.


Refrigerant-134a is throttled from the saturated liquid
state at 700 kPa to a pressure of 160 kPa. Determine the temperature
drop during this process and the final specific volume
of the refrigerant. Explain this temperature drop.


A hot-water stream at 80°C enters a mixing chamber
with a mass flow rate of 0.5 kg/s where it is mixed with a
stream of cold water at 20°C. If it is desired that the mixture
leave the chamber at 42°C, determine the mass flow rate of the
cold-water stream. Assume all the streams are at a pressure of
250 kPa.


Refrigerant-134a at 1 MPa and 90°C is to be cooled
to 1 MPa and 30°C in a condenser by air. The air enters at
100 kPa and 27°C with a volume flow rate of 600 m
3/min
and leaves at 95 kPa and 60°C. Determine the mass flow rate
of the refrigerant.

 

mim-shimi

عضو جدید
کاربر ممتاز
آره خوب خیلی مهمه
این دفعه ای که پیچونده با ای میلی که فرستاده
فعلا همین یکی:



An adiabatic air compressor is to be powered by a direct-coupled adiabaticsteam turbine that is also
driving a generator. Steam enters the turbine at 12.5 MPa and 500°C at a rate of 25 kg/s and exits at 10
kPa and a quality of 0.92. Air enters the compressor at 98 kPa and 295 K at a rate of 10 kg/s and exits at 1
MPa and 620 K. Determine the net power delivered to the generator by the turbine.​
 

sami-jun

عضو جدید
این سوالو کسی بلده؟؟؟؟؟؟:)
find the equation for the work of a reversible,isothermal compression of 1 mol of gas in apiston/cylinder assembly if the molar volume of the gas is given by
v=(RT/p)+b
where b and R are positive constants
 
این سوالو کسی بلده؟؟؟؟؟؟:)
find the equation for the work of a reversible,isothermal compression of 1 mol of gas in apiston/cylinder assembly if the molar volume of the gas is given by
v=(RT/p)+b
where b and R are positive constants
كار فرايند همدما (براي گاز) ميشه :
w=PVLn(p1/p2)=RTLn(V2/V1)
V-b رو بجاي V مي ذاري
 
آره خوب خیلی مهمه
این دفعه ای که پیچونده با ای میلی که فرستاده
فعلا همین یکی:



An adiabatic air compressor is to be powered by a direct-coupled adiabaticsteam turbine that is also
driving a generator. Steam enters the turbine at 12.5 MPa and 500°C at a rate of 25 kg/s and exits at 10
kPa and a quality of 0.92. Air enters the compressor at 98 kPa and 295 K at a rate of 10 kg/s and exits at 1
MPa and 620 K. Determine the net power delivered to the generator by the turbine.​
ببين اينو درست متوجه شدم ؟

يه توربيني كه كوپل شده با يه كمپرسور هوا و اينو راه ميندازه و از طرفي يه ژنراتور هم راه ميندازه ؟
 

sami-jun

عضو جدید
ببين اينو درست متوجه شدم ؟

يه توربيني كه كوپل شده با يه كمپرسور هوا و اينو راه ميندازه و از طرفي يه ژنراتور هم راه ميندازه ؟

نیما منم فکر کنم منظورش همین باشه ولی گفته کار کل چطور باید بدستش بیاریم؟
 

sami-jun

عضو جدید
سلام
ماشاالله استاد ما زیادی فعاله;)
فعلا سوالا رو میزارم اینجا..لطف کنین روش فکر کنین..شنبه اشکالامو ازتون میپرسم:)
ممنون از همه



For All these problem you need to determine your control volume schematically
.
Refrigerant-134a enters an adiabatic compressor as saturated vapor at -24°C and leaves at 0.8
MPa and 60°C. The mass flow rate of the refrigerant is 1.2 kg/s. Determine
([FONT=TimesNewRoman,Italic]a[/FONT]) the power input to the compressor and ([FONT=TimesNewRoman,Italic]b[/FONT]) the volume
flow rate of the refrigerant at the compressor inlet.


Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 10 MPa,
450°C, and 80 m/s, and the exit conditions are 10 kPa, 92 percent quality, and 50m/s. The mass
flow rate of the steam is 12 kg/s. Determine ([FONT=TimesNewRoman,Italic]a[/FONT]) the change in kinetic energy, ([FONT=TimesNewRoman,Italic]b[/FONT]) the power output,
and ([FONT=TimesNewRoman,Italic]c[/FONT]) the turbine inlet area.


Refrigerant-134a is throttled from the saturated liquid
state at 700 kPa to a pressure of 160 kPa. Determine the temperature
drop during this process and the final specific volume
of the refrigerant. Explain this temperature drop.


A hot-water stream at 80°C enters a mixing chamber
with a mass flow rate of 0.5 kg/s where it is mixed with a
stream of cold water at 20°C. If it is desired that the mixture
leave the chamber at 42°C, determine the mass flow rate of the
cold-water stream. Assume all the streams are at a pressure of
250 kPa.


Refrigerant-134a at 1 MPa and 90°C is to be cooled
to 1 MPa and 30°C in a condenser by air. The air enters at
100 kPa and 27°C with a volume flow rate of 600 m3/min
and leaves at 95 kPa and 60°C. Determine the mass flow rate
of the refrigerant.

1.
process:steady state
mass ballance:mdoti=mdote=mdot
energy eq:qdot-wdot+mdot*hi-mdot*he=0
adibatic q=0
mdot=1.2,hi=hg'-24c,he from steam table at .8 mpa 60c
then wdot found
بقیشم بلدم هرکجا اشکال داشتید در خدمتم
 
نیما منم فکر کنم منظورش همین باشه ولی گفته کار کل چطور باید بدستش بیاریم؟
كاري رو ميخواد كه به ژنراتور ميرسه
توربين يه كار واسه كمپرسور توليد ميكنه يه كارم واسه ژنراتور . البته اگه اينجوري گفته باشه .
كار كمپرسور رو ميشه از اطلاعات داده شده بدست آورد
كار توربينم بدست مياد از اطلاعاتش
وقتي از هم كمش كنيم ميشه كار ژنراتور ;)
 

mim-shimi

عضو جدید
کاربر ممتاز
آره؟؟؟؟؟؟؟؟خب دقیقا باید برا رفع اشکال پیش کی بیایم؟
 
آره؟؟؟؟؟؟؟؟خب دقیقا باید برا رفع اشکال پیش کی بیایم؟
شما همه همكلاسي هستين كه توي اين تاپيك پست ميديد؟!!!
فردا استادتونم مياد سوالارو از هيمنجا ميبره واستون كپي ميگيره! :biggrin:
 

JU JU

کاربر حرفه ای
کاربر ممتاز
سیالات 2 فازی

سیالات 2 فازی

منم سوالمو مطرح کنم
کسی هست آیا مرا یاری نماید ؟

-----------------------------------

هوا با فشار 200atm و دمای 100c به یک نازل همگرا-واگرا که سطح مقطع گلوگاه نصف سطح مقطع خروجی آن است وارد میشود، برای N(ma)=0.8

P, T,U, ro
دانسیته سیال و فلاکس را محاسبه کنید

ب- شرایط P*, T*, U*, G*,i ( اون i آخرب الکیه فقط گذاشتم استارا سره جاشون باشه)

ج- اگر بخواهیم از این نازل برای ایجاد جریان مافوق صوت استفاده کنیم Nma (ان ماخ ) را در انتهای نازل محاسبه کنید

MW air = 20
gama= Cp/Cr=1.4

--------------------------------------

امیدوارم هم اینک جواب زیبایتان را ببینم :w05::heart::gol:
 

JU JU

کاربر حرفه ای
کاربر ممتاز
ماخ نامبره
M=V/c

مجذورشو هم بنویسم ؟

اون استارها یعنی در حالت بحرانی !!
 
منم سوالمو مطرح کنم
کسی هست آیا مرا یاری نماید ؟

-----------------------------------

هوا با فشار 200atm و دمای 100c به یک نازل همگرا-واگرا که سطح مقطع گلوگاه نصف سطح مقطع خروجی آن است وارد میشود، برای N(ma)=0.8

P, T,U, ro
دانسیته سیال و فلاکس را محاسبه کنید

ب- شرایط P*, T*, U*, G*,i ( اون i آخرب الکیه فقط گذاشتم استارا سره جاشون باشه)

ج- اگر بخواهیم از این نازل برای ایجاد جریان مافوق صوت استفاده کنیم Nma (ان ماخ ) را در انتهای نازل محاسبه کنید

MW air = 20
gama= Cp/Cr=1.4

--------------------------------------

امیدوارم هم اینک جواب زیبایتان را ببینم :w05::heart::gol:

الف:
m.=ro.u.A
u سرعته كه با فرمول ماخ بدست مياد
ro هم اگه هوا رو گاز ايده آل فرض كنيم ميشه :‌ro=PM/RT
A هم كه چيزي نداده . دبي جرمي بر حسب قطر بدست مياد
------
ب:سرعت مينيمم بايد با سرعت صوع يكي باشه ديگه . عدد ماخ مينيمم 1 ميشه
نميدونم اينا چين اصلا! آخه بحراني از چه لحاظ؟!
--------

ج:
 

k_siroos

مدیر بازنشسته
منم سوالمو مطرح کنم
کسی هست آیا مرا یاری نماید ؟

-----------------------------------

هوا با فشار 200atm و دمای 100c به یک نازل همگرا-واگرا که سطح مقطع گلوگاه نصف سطح مقطع خروجی آن است وارد میشود، برای N(ma)=0.8

P, T,U, ro
دانسیته سیال و فلاکس را محاسبه کنید

ب- شرایط P*, T*, U*, G*,i ( اون i آخرب الکیه فقط گذاشتم استارا سره جاشون باشه)

ج- اگر بخواهیم از این نازل برای ایجاد جریان مافوق صوت استفاده کنیم Nma (ان ماخ ) را در انتهای نازل محاسبه کنید

MW air = 20
gama= Cp/Cr=1.4

--------------------------------------

امیدوارم هم اینک جواب زیبایتان را ببینم :w05::heart::gol:


سلام JuJu جان ، اگه کتاب عملیات واحد مک کیب (بهرام پوستی- جلد1 ) رو داری صفحه 137 رو یه نگاه بنداز ، این مثال دقیقا اونجا هست فقط دما و فشارش فرق می کنه ...

اون حروف استار دار هم حالت بحرانی بهش نمی گن ، می گن ستاره دار( مثلا فشار ستاره دار) که برای شرایطی اند که Ma=1 است . هر جا هم زیر نویس t دیدی مربوط به گلوگاه است (Throttle) ...
موفق باشی ... :gol::heart:
 

JU JU

کاربر حرفه ای
کاربر ممتاز
سلام JuJu جان ، اگه کتاب عملیات واحد مک کیب (بهرام پوستی- جلد1 ) رو داری صفحه 137 رو یه نگاه بنداز ، این مثال دقیقا اونجا هست فقط دما و فشارش فرق می کنه ...

اون حروف استار دار هم حالت بحرانی بهش نمی گن ، می گن ستاره دار( مثلا فشار ستاره دار) که برای شرایطی اند که Ma=1 است . هر جا هم زیر نویس t دیدی مربوط به گلوگاه است (Throttle) ...
موفق باشی ... :gol::heart:

پسل، من کتاب ترجمش رو ندارم، انگلیسیه، البته عملیات جلد 2 فارسیشو دارم

حالا فصل و بخش مربوطه رو بگووو :child:
 

sami-jun

عضو جدید
please answer it
if the heat capacity of a substance is correctly represented by an equation of the form
cp=A+BT+CT^2
SHOW THAT THE ERROR RESULTING WHEN CPH IS ASSUMED EQUAL TO CP EVALUATED AT THE ARITHMETIC MEAN OF THE INITAL AND FINAL TEMPRETURE IS
C*(T2-T1)^2/12
 
please answer it
if the heat capacity of a substance is correctly represented by an equation of the form
cp=A+BT+CT^2
SHOW THAT THE ERROR RESULTING WHEN CPH IS ASSUMED EQUAL TO CP EVALUATED AT THE ARITHMETIC MEAN OF THE INITAL AND FINAL TEMPRETURE IS
C*(T2-T1)^2/12
اين چيه ؟ CPH

ولي فك كنم اينو تو كتاب وننس ديدم يه زماني !
بايد از فرمون cp متوسط استفاده كني
cp=انتگرالcp از T1 تا T2 تقسيم بر T2-T1
فك كنم اين بود . يادم رفته!
 

sami-jun

عضو جدید
اين چيه ؟ CPH

ولي فك كنم اينو تو كتاب وننس ديدم يه زماني !
بايد از فرمون cp متوسط استفاده كني
cp=انتگرالcp از T1 تا T2 تقسيم بر T2-T1
فك كنم اين بود . يادم رفته!

اره سوال 6 از فصل 4 ون نسه
اینجوری که گفتیدکه بدست نمیاد
 
آخرین ویرایش:

JU JU

کاربر حرفه ای
کاربر ممتاز
please answer it
if the heat capacity of a substance is correctly represented by an equation of the form
cp=A+BT+CT^2
SHOW THAT THE ERROR RESULTING WHEN CPH IS ASSUMED EQUAL TO CP EVALUATED AT THE ARITHMETIC MEAN OF THE INITAL AND FINAL TEMPRETURE IS
C*(T2-T1)^2/12

Cp = A+BT + C/3 (4T^2 - T1T2

Cp*= A +BT+CT^2

gama = C/3 (4T^2 - T1T2) - CT^2 = C/3 (T^2-T1T2) = C/3[ (T1+T2)/2 - T1T2 ] = C/3 [ (T1^2 +2T1T2 6+ 2T2^2)/4 - T1T2] = C/12 (T1^2 - 2T1T2 + T2^2) = [C(T2-T1)^2 / 12
 

sami-jun

عضو جدید
Cp = A+BT + C/3 (4T^2 - T1T2

Cp*= A +BT+CT^2

gama = C/3 (4T^2 - T1T2) - CT^2 = C/3 (T^2-T1T2) = C/3[ (T1+T2)/2 - T1T2 ] = C/3 [ (T1^2 +2T1T2 6+ 2T2^2)/4 - T1T2] = C/12 (T1^2 - 2T1T2 + T2^2) = [C(T2-T1)^2 / 12

این فرمول cp اولی رو از کجا اووردی؟
یه کم بیشتر توضیح میدی؟
 

JU JU

کاربر حرفه ای
کاربر ممتاز
please answer it
if the heat capacity of a substance is correctly represented by an equation of the form
cp=A+BT+CT^2
SHOW THAT THE ERROR RESULTING WHEN CPH IS ASSUMED EQUAL TO CP EVALUATED AT THE ARITHMETIC MEAN OF THE INITAL AND FINAL TEMPRETURE IS
C*(T2-T1)^2/12

Cp = A+BT + C/3 (4T^2 - T1T2

Cp*= A +BT+CT^2

gama = C/3 (4T^2 - T1T2) - CT^2 = C/3 (T^2-T1T2) = C/3[ (T1+T2)/2 - T1T2 ] = C/3 [ (T1^2 +2T1T2 6+ 2T2^2)/4 - T1T2] = C/12 (T1^2 - 2T1T2 + T2^2) = [C(T2-T1)^2 / 12


معادله 7-4 (معادله هفت فصل 4 ) ( البته این تو کتاب فارسیشه ) رو یه نگاهی بندازین
Cp = A+BT + C/3 (4T^2 - T1T2) +D/T1T2

تو صفحه هات کتاب و توضیحاتی که واسه این فرمول بدست میاد
حالا به سوال دقت کنین
کجا و کی D صفر هستش ؟ اینجا D صفر فرض شده،چرا ؟
برگردیم به صورت سوال
cp=A+BT+CT^2
اینجا DT^-2 میبینیم ؟ پس D نداریم، صفره
این از معادله ظرفیت گرمایی فشار ثابت ( همون اولای فصل 4 در مورد این مبحث بحث شده )




Cp*= A +BT+CT^2
اگه فرض این باشه که Cp ظرفیت گرمایی در دمای Tam باشد. در اینصورت معادله Cp* رو که در بالا بهش اشاره کردم داریم

اینا معادلات و فرضیات بود که از معادلات درون کتاب گرفته شده و بر اساس صورت مسئله

بقیش کافیه این دو معادله رو تفریق کنیم و ادامه داستان


فکر کنم توضیحاتم بد نبود

وقتی دو معادله تفریق بشه حاصل تفریق، خطا رو بیان میکنه


* من حلش رو داشتم، تو کتاب با مداد نوشتم، با توضیحاتش که الان اضاف شد
 

mim-shimi

عضو جدید
کاربر ممتاز
انتقال حرارت

انتقال حرارت

A furnace wall is made of 75mm thick fire clay brick and 6.4mm thick mild steel plate.the inside surface of brick is T=647 and outside air temperatire is 27.determine:
a)the heat loss per m^2 area of the furnace wall and outside surface temperature of the steel plate.
b)if 18 steel bolts each of 19mm diameter are used for fixing the steel plate on the brick wall per m^2 area of the wall,what is the percentage increase in the heat flux?

k(brick=1.1 k(steel=39
h(outside heat transfer coefficient=68
 

mim-shimi

عضو جدید
کاربر ممتاز
ترمو2

ترمو2

سوال 6.13 از کتاب ون نس یعنی باید از روابط 6.46 و 6.49 بریم و dp رو از رابطه ای که تو سوال داده بدست بیاریم و جایگزین کنیم؟؟؟؟؟؟؟؟؟؟؟؟؟؟؟؟؟
خیلی کوفته که:confused:...
 
A furnace wall is made of 75mm thick fire clay brick and 6.4mm thick mild steel plate.the inside surface of brick is T=647 and outside air temperatire is 27.determine:
a)the heat loss per m^2 area of the furnace wall and outside surface temperature of the steel plate.
b)if 18 steel bolts each of 19mm diameter are used for fixing the steel plate on the brick wall per m^2 area of the wall,what is the percentage increase in the heat flux?

k(brick=1.1 k(steel=39
h(outside heat transfer coefficient=68
قسمت a كه آسونه . با استفاده از قانون مقاومت ها مجهول q بدست مياد
قسمت b هم منظورشو نفهميدم !
 
بالا